CITROEN C3 UK Recall Check

---

Recalls Number (Vehicles Effected)

R/2023/335 (17)

Manufacturer Reference

MB4/231198EE

Defect

On affected vehicles the fuel tank is not to specification due to a deviation in the manufacturing process which could lead to a potential risk of fuel seepage.

Remedy

Replace fuel tank.

---

Recalls Number (Vehicles Effected)

R/2023/220 (372)

Manufacturer Reference

JJN/ 221334EE

Defect

Affected vehicles may have been fitted with a rear axle crossmember that was not manufactured according to specifications.

Remedy

Check and replace the rear axle crossmember if necessary.

---

Recalls Number (Vehicles Effected)

R/2019/339 (1080)

Manufacturer Reference

GYY

Defect

Front air bag igniters may not deploy correctly.

Remedy

Check and if necessary replace the affected front airbags.

---

Recalls Number (Vehicles Effected)

R/2020/165 (10)

Manufacturer Reference

HFV

Defect

The steering geometry could be incorrectly set due to an incorrectly calibrated setting rig in the manufacturing plant.

Remedy

Check the steering alignment and adjusting if set incorrectly. If the front tyres are worn these will also be replaced.

---

Recalls Number (Vehicles Effected)

R/2019/353 (16144)

Manufacturer Reference

GWK

Defect

Engine management software issue could result in incorrect emission levels.

Remedy

Update the engine management software.

---

Recalls Number (Vehicles Effected)

R/2019/009 (78)

Manufacturer Reference

GRE

Defect

"The universal clamp fixing bolt is not correctly fitted in the recess at the end of thesteering column."

Remedy

Check and if necessary refit the steering column universal joint fixing.

---

Recalls Number (Vehicles Effected)

R/2018/197 (392)

Manufacturer Reference

GLJ

Defect

On the affected vehicles the crimping preventing lateral movement of the steering column bearing may not be correct to specification. This may result in noise and play in the steering. Ultimately it could lead to steering malfunction.

Remedy

The remedy involves checking the crimping on the steering column and replacing the steering column if necessary.

---

Recalls Number (Vehicles Effected)

R/2017/339 (75)

Manufacturer Reference

GFP

Defect

An engine component may not be to specification which could result in loss of engine performance. This may lead to the engine stalling and potentially causing an engine failure. In very unlikely circumstances the vehicle speed may increase without warning but will stop on its own after a few seconds.

Remedy

On affected vehicles carry out a functional diagnostic check of the engine. If necessary replace the engine.

---

Recalls Number (Vehicles Effected)

R/2017/180 (8)

Manufacturer Reference

GAM

Defect

A component within the left-hand curtain airbag may not conform to specification and the air bag may not deploy correctly.

Remedy

On affected vehicles replace the left hand curtain air bag.

---

Recalls Number (Vehicles Effected)

R/2017/181 (5)

Manufacturer Reference

GAQ

Defect

A component within the right-hand curtain airbag may not conform to specification and the air bag may not deploy correctly.

Remedy

On affected vehicles replace the right hand curtain air bag.

---

Recalls Number (Vehicles Effected)

R/2017/139 (3607)

Manufacturer Reference

NYD

Defect

A possible nonconformity of an internal component of the starter motor relay could affect the control of the starter motor. This could adversely affect the starting operation and damage the starter motor due to overheating and in extreme cases there is a risk of fire.

Remedy

On affected vehicles check and where necessary replace the starter motor relay.

---

Recalls Number (Vehicles Effected)

R/2017/089 (65)

Manufacturer Reference

NYK

Defect

The ignition module which triggers the front seat airbag may not deploy in the event of an impact. There is no indication to the driver the unit is faulty.

Remedy

Recall the vehicles that are likely to be affected and replace the front seat airbag unit.

---

Recalls Number (Vehicles Effected)

R/2016/229 (787)

Manufacturer Reference

NSV

Defect

In the event of emergency braking or during an ESP regulation phase (e.g. avoiding manoeuvre) the hydraulic block may not prevent the locking of a wheel which could affect control of the vehicle.

Remedy

On affected vehicles replace the braking system hydraulic block

---

Recalls Number (Vehicles Effected)

R/2016/042 (17)

Manufacturer Reference

NRC

Defect

An oil leak could develop at the turbocharger lubrication union retaining bolt due to a non-conformity of this part.

Remedy

On affected vehicles replace the turbocharger lubrication union bolt and its seals.

---

Recalls Number (Vehicles Effected)

R/2015/061 (24)

Manufacturer Reference

NHR

Defect

It is possible that the front subframe and suspension wishbones mounting bolts may not have been torqued to the correct specification. This could result in the mounting bolt working loose and falling from the vehicle plus the possibility of the insecurity of the subframe or the front suspension wishbone. This can cause an issue with the handling or even loss of control of the vehicle.

Remedy

Recall all affected vehicles to check and retorque the front subframe and suspension wishbone mounting bolts.

---

Recalls Number (Vehicles Effected)

R/2014/083 (28)

Manufacturer Reference

NEB

Defect

Front subframes on affected vehicles may show signs of damage to the left hand mounting point caused during the manufacturing process. Over time this may affect durability and cause the mounting to fail. This can affect security of components attached to the subframe and may affect control of the vehicle.

Remedy

Prior to failure the driver should notice excessive noise from this area. As a safety measure affected vehicles should be checked and where necessary the subframe replaced.

---

Recalls Number (Vehicles Effected)

R/2014/047 (3092)

Manufacturer Reference

NBH

Defect

The front suspension wishbone mounting bolts might not have been manufactured to the correct specification potentially causing a risk of these parts breaking. Broken mounting bolts can be noticed by the driver through noises and poor directional control.

Remedy

Recall the vehicles that are likely to be affected to replace the front suspension wishbone mounting bolts.

---

Recalls Number (Vehicles Effected)

R/2014/025 (279)

Manufacturer Reference

NAZ

Defect

It has been established that the high pressure fuel rail pipes on the engine have not been torqued to the correct specification. This can result in poor sealing of the rail which can cause as fuel leak onto the engine. If the vaporised fuel comes into contact with a hot engine component there can be a risk of an engine bay fire.

Remedy

Recall all the affected vehicles and retorque the high pressure fuel rail pipes.

---

Recalls Number (Vehicles Effected)

R/2013/068 (19)

Manufacturer Reference

MWH

Defect

It has been identified that it is possible that the rear screen seal may not be to specification. This could lead to water ingress into the boot area which in extreme cases could cause the rear screen to become insecure in its housing.

Remedy

Recall all affected vehicles and replace the rear screen seal.

---

Recalls Number (Vehicles Effected)

R/2012/129 (1169)

Manufacturer Reference

MQM

Defect

It has been established that the con-rod (big end) shell bearings may not have been manufactured to specification. This could lead to premature deterioration of the shells and if not identified it could result in engine failure.

Remedy

Recall affected vehicles and replace con-rod shell bearings.

---

Recalls Number (Vehicles Effected)

R/2012/126 (49)

Manufacturer Reference

MSK

Defect

The nearside front brake hose may not be properly secured and could chafe. If not noticed the chafing could cause loss of brake fluid and the warning lamp to illuminate. Additionally it is possible the braking efficiency could be adversely affected.

Remedy

Recall the vehicles that are likely to be affected to check and where necessary correctly secure the nearside front brake hose or replace the hose.

---

Recalls Number (Vehicles Effected)

R/2012/123 (129)

Manufacturer Reference

MSN

Defect

It is possible that the left hand wheel bolts may not have been torqued to the correct specification. This could lead to noise or vibration from the wheels and if not rectified it could result in wheel detachment and loss of control of the vehicle.

Remedy

Recall affected vehicles to check and if necessary re-torque the wheel bolts.

---

Recalls Number (Vehicles Effected)

R/2012/076 (123)

Manufacturer Reference

MQV

Defect

The battery earth cable dimensions are incorrect and may cause the cable to break. This will then cause the engine to cut out.

Remedy

Replace the battery negative cable with a new dimension cable. (length and terminal)

---

Recalls Number (Vehicles Effected)

R/2012/074 (963)

Manufacturer Reference

MQC

Defect

The ABS block may not conform to manufacturer specification. This could affect the operation of the ABS/ESP systems on the rare occasions that they are activated.

Remedy

The hydraulic ABS/ESP block will be checked and if necessary replaced.

---

Recalls Number (Vehicles Effected)

R/2012/062 (981)

Manufacturer Reference

MPG

Defect

The engine may cut out as a dimensional nonconformity of the earth cable could lead to it breaking.

Remedy

Recall the vehicles that are likely to be affected to replace the battery earth cable.

---

Recalls Number (Vehicles Effected)

R/2012/033 (2)

Manufacturer Reference

MEP

Defect

There is a possibility that a component internal to the steering mechanism may not be manufactured to the correct specification which over time can cause the steering to become either stiff or easier to operate.

Remedy

Recall the vehicles that are likely to be affected to replace the steering mechanism.

---

Recalls Number (Vehicles Effected)

R/2012/022 (2712)

Manufacturer Reference

MPF

Defect

The battery earth return cable is not to the correct specification which during vehicle operation may cause it to fail. This could result in the engine cutting out.

Remedy

Recall all affected vehicle and replace the battery earth return cable.

---

Recalls Number (Vehicles Effected)

R/2012/005 (1276)

Manufacturer Reference

MNR

Defect

The battery earth return cable is not to the correct specification which during vehicle operation may cause it to fail. This could result in the engine cutting out.

Remedy

Recall all affected vehicle and replace the battery earth return cable.

---

Recalls Number (Vehicles Effected)

R/2011/165 (7)

Manufacturer Reference

MNT

Defect

The front suspension lower swivel joint may not be tightened correctly. If the bolt slackens the joint may separate. This could adversely affect the directional control of the vehicle.

Remedy

Recall the vehicles that are likely to be affected to check and where necessary correct the tightening torque of the lower swivel joint clamp bolt.

---

Recalls Number (Vehicles Effected)

R/2011/156 (589)

Manufacturer Reference

MNE

Defect

The earth cable for the battery may be too short and could break. If this happens the vehicle electrical circuit will fail. This could cause the engine to cut out.

Remedy

Recall all affected vehicles and replace the battery earth cable.

---

Recalls Number (Vehicles Effected)

R/2011/137 (25)

Manufacturer Reference

MMT

Defect

On affected vehicles the drivers airbag nay not be of conformity. This non-conformity could lead to poor deployment of the airbag in the event of a collision.

Remedy

Replace drivers airbag

---

Recalls Number (Vehicles Effected)

R/2011/120 (9175)

Manufacturer Reference

MLY

Defect

The battery earth return cable maybe too short which during vehicle operation may cause it to fail at its gearbox mounting point. This could result in the engine cutting out.

Remedy

Recall all affected vehicle and replace the battery earth return cable.

---

Recalls Number (Vehicles Effected)

R/2011/113 (34)

Manufacturer Reference

MME

Defect

The tailgate may fall from the open position because of a potentially faulty ball joint to strut link.

Remedy

Recall the vehicles that are likely to be affected to check and if necessary replace the tailgate struts.

---

Recalls Number (Vehicles Effected)

R/2011/104 (1057)

Manufacturer Reference

MLZ

Defect

The fixing bracket of the air unit on the engine may break under the effect of vibration. This could affect some of the surrounding components.

Remedy

Remove the bracket and replace with washers

---

Recalls Number (Vehicles Effected)

R/2011/087 (3773)

Manufacturer Reference

MHM

Defect

A component within the parking brake assembly may not meet conformity this could result in a lengthening of the handbrake travel which could have an affect on the parking brake efficiency.

Remedy

Recall the affected vehicles and replace the non-conformity components.

---

Recalls Number (Vehicles Effected)

R/2011/062 (22)

Manufacturer Reference

MLA

Defect

On the affected vehicles an internal component of the braking assistance circuit amplifier may not be in conformity. This could result in reduction of braking over time.

Remedy

Replacement of the amplifier (Servo).

---

Recalls Number (Vehicles Effected)

R/2011/003 (38)

Manufacturer Reference

MHJ

Defect

Possible nonconformity of the welding between the cross rail under the floor and its end piece. This possible nonconformity may mean that the rear seats are not held correctly in place in the event of a serious impact.

Remedy

Checking of the assembly and repair if necessary.

---

Recalls Number (Vehicles Effected)

R/2010/192 (72)

Manufacturer Reference

MHB

Defect

Due to incorrect machining it is possible that the crankshaft is not to the correct specification which can lead to insufficient lubrication of the crankshaft and subsequent engine failure.

Remedy

Recall all affected vehicles and replace the engine.

---

Recalls Number (Vehicles Effected)

R/2010/155 (12950)

Manufacturer Reference

MFL

Defect

It has been identified that the position of the exterior lighting control ring may not be detected by the lighting management system and the lights may switch off without warning.

Remedy

Recalled vehicles will have the lighting management software updated.

---

Recalls Number (Vehicles Effected)

R/2010/146 (44)

Manufacturer Reference

MGQ

Defect

The fuel tank mounting bolts may have been incorrectly torqued this may cause the mountings to become loose which can lead to stress on the fuel pipes and subsequently a fuel leak.

Remedy

Recall the affected vehicles to check and if necessary retorque of the mounting bolts.

---

Recalls Number (Vehicles Effected)

R/2010/136 (67)

Manufacturer Reference

MGN

Defect

The bonnet lock fixing bolts may not be fully secure which can result in noise and vibration and in rare cases insecure holding by the bonnet catch and lock.

Remedy

On recalled vehicles the tightness of the bonnet lock fixing bolts will be checked and where necessary tightened to specification.

---

Recalls Number (Vehicles Effected)

R/2010/132 (16)

Manufacturer Reference

MFQ

Defect

The bolts securing the engine cradle to the chassis may not be fully secure. There is a possibility that the bolts may loosen which will result in noise vibration and in rare cases an alteration in vehicle handling.

Remedy

Recall the vehicles that are likely to be affected to replace all the securing bolts and tighten them to the correct specification.

---

Recalls Number (Vehicles Effected)

R/2010/086 (7760)

Manufacturer Reference

MFF

Defect

It has been established that on some C3's the rigid section of the front brake hose may be deformed or twisted. This could result in a deterioration of the braking efficiency.

Remedy

Recall the affected vehicles and inspect the brake hose for distortion and replace if required.

---

Recalls Number (Vehicles Effected)

R/2010/076 (36)

Manufacturer Reference

MFV

Defect

The front axle fixings may not have been tightened sufficiently. This may result in the front axle becoming insecure which may in rare cases if not corrected cause directional control to become impaired.

Remedy

Recall the vehicles that are likely to be affected to check the front axle fixings and where necessary tighten them to specification.

---

Recalls Number (Vehicles Effected)

R/2010/043 (114)

Manufacturer Reference

MEZ

Defect

The front right hand drive-shaft may fail.

Remedy

Recall the affected vehicles to check and if necessary replace the right hand drive-shaft

---

Recalls Number (Vehicles Effected)

R/2009/113 (37086)

Manufacturer Reference

MBT

Defect

It has been identified that due to incorrect positioning of the exterior lighting control ring by the lighting management system the lights may switch off unexpectedly.

Remedy

Recalled vehicles will have the lighting management software updated

---

Recalls Number (Vehicles Effected)

R/2009/096 (754)

Manufacturer Reference

MCD

Defect

The parking brake may fail due to the cable not being manufactured to specification.

Remedy

Recall the vehicles that are likely to be affected to replace the parking brakes cables.

---

Recalls Number (Vehicles Effected)

R/2008/199 (6031)

Manufacturer Reference

MAQ

Defect

An incorrect engine relay unit may have been fitted. This ECU could deteriorate and cause operating faults and perhaps failure of certain equipment

Remedy

Recall affected vehicles check Engine Relay Unit and replace if not correct specification.

---

Recalls Number (Vehicles Effected)

R/2008/150 (4652)

Manufacturer Reference

Defect

The tightening torque for the front suspension wishbone mounting bolts has proved insufficient. This can lead to loosening represented by abnormal noise

Remedy

Recall affected vehicles and retorque front suspension wishbone bolts

---

Recalls Number (Vehicles Effected)

R/2006/225 (4032)

Manufacturer Reference

XZT

Defect

If the battery voltage is abnormally low the antilock braking system electronic control unit may not perform to specification which in rare cases may cause a reduction in braking efficiency.

Remedy

Recall the vehicles that are likely to be affected to replace the Electronic Control Unit.

---

Recalls Number (Vehicles Effected)

R/2006/051 (9868)

Manufacturer Reference

Defect

It has been identified that the accelerator pedal can return too slowly. This can have an effect on the driving of the vehicle

Remedy

Recalled vehicles will have the accelerator pedal replaced.

---

Recalls Number (Vehicles Effected)

R/2005/185 (6772)

Manufacturer Reference

XWZ

Defect

This concern relates to right hand drive vehicles only. There may cases of the brake linkage lever being defectively assembled which may result in a loss of braking efficiency.

Remedy

Recall the vehicles that are likely to be affected check and where necessary reposition the brake pedal relay linkage lever.

---

Recalls Number (Vehicles Effected)

R/2005/147 (56604)

Manufacturer Reference

XWJ (C3)

Defect

In the exceptional event of a spring breaking there could be a risk of the spring making contact with the vehicle tyre.

Remedy

Recall the vehicles that are likely to be affected and fit a suspension cup to each side of the front suspension.

---

Recalls Number (Vehicles Effected)

R/2005/020 (64)

Manufacturer Reference

Defect

The C3 vehicles concerned are fitted with a panoramic sunroof in respect of which the mobile glass has securing nuts that do not meet the manufacturer's quality requirements.

Remedy

Recall affected vehicles and replace the sunroof securing nuts.

---

Recalls Number (Vehicles Effected)

R/2004/022 (381)

Manufacturer Reference

Defect

Possibility that roof bars may slip when bulky objects are placed on them

Remedy

Recall affected vehicles and replace roof bars with modified type.

---

Recalls Number (Vehicles Effected)

R/2003/016 (5032)

Manufacturer Reference

Defect

Water ingress to the ABS ECU connector may cause a malfunction of the anti lock braking system. In the worst case water contamination could cause a short circuit and fire in the ABS control unit.

Remedy

Protect the ABS connector from water ingress. Replace the ABS ECU if found necessary.

---

Recalls Number (Vehicles Effected)

R/2002/174 (361)

Manufacturer Reference

XME

Defect

The front passenger air bag may not fully deploy in an impact.

Remedy

Fit a replacement air bag.

---

Recalls Number (Vehicles Effected)

R/2002/121 (2828)

Manufacturer Reference

XKE

Defect

The front suspension lower ball joint pinch bolts may not have been fully tightened. In the worst case separation of the ball joint from the suspension arm would affect directional control of the vehicle.

Remedy

Check the ball joint pinch bolts for correct torque and tighten where necessary.