CITROEN C4 UK Recall Check

---

Recalls Number (Vehicles Effected)

R/2023/141 (6867)

Manufacturer Reference

JTF/221078CO

Defect

On affected vehicles the AC compressor stator wiring could develop a fault leading to current loss inside the AC compressor that could result in a vehicle powertrain shutdown when driving.

Remedy

Reprogram the Powertrain Diagnosis ECU with updated software.

---

Recalls Number (Vehicles Effected)

R/2022/230 (1)

Manufacturer Reference

JHC

Defect

The rear hub bearing locating bolts may be incorrectly tightened.

Remedy

Check the torque of the rear hub bolts and replace the hub(s) and the bolts if necessary

---

Recalls Number (Vehicles Effected)

R/2019/339 (1080)

Manufacturer Reference

GYY

Defect

Front air bag igniters may not deploy correctly.

Remedy

Check and if necessary replace the affected front airbags.

---

Recalls Number (Vehicles Effected)

R/2019/329 (5290)

Manufacturer Reference

GUM

Defect

The calibration of the engine management software could result in emissions of NOx which do not comply with the regulatory limits.

Remedy

Download new engine management software

---

Recalls Number (Vehicles Effected)

R/2018/178 (138)

Manufacturer Reference

GKA

Defect

Engine could overheat leading to failure in extreme cases

Remedy

Download new engine management software

---

Recalls Number (Vehicles Effected)

R/2018/049 (2098)

Manufacturer Reference

GFJ

Defect

The engine electronic cooling management control strategy and the maximum temperature alert threshold could cause the engine to overheat. This could result in a warning light and a message being displayed on the instrument panel.

Remedy

"On affected vehicles download a new engine management software in order to modifythe cooling management parameters to improve the control of the engine operating temperature."

---

Recalls Number (Vehicles Effected)

R/2017/339 (75)

Manufacturer Reference

GFP

Defect

An engine component may not be to specification which could result in loss of engine performance. This may lead to the engine stalling and potentially causing an engine failure. In very unlikely circumstances the vehicle speed may increase without warning but will stop on its own after a few seconds.

Remedy

On affected vehicles carry out a functional diagnostic check of the engine. If necessary replace the engine.

---

Recalls Number (Vehicles Effected)

R/2017/290 (11)

Manufacturer Reference

GDT

Defect

"A nonconformity of the windscreen wiper motor breather system could in some cases resultin the entry of water and complete jamming of the motor due to internal corrosion."

Remedy

On affected vehicles replace the wiper motor.

---

Recalls Number (Vehicles Effected)

R/2017/289 (11)

Manufacturer Reference

GDT

Defect

Non-conformity of a tailgate strut internal component may allow corrosion to develop. This may cause the strut to fail and the tailgate may not be held open.

Remedy

On affected vehicles replace the struts.

---

Recalls Number (Vehicles Effected)

R/2017/208 (2014)

Manufacturer Reference

GBN

Defect

The positioning of the starter motor supply terminal may not conform to specification. Contact with a neighbouring component could cause a short circuit.

Remedy

On affected vehicles check the position of the terminal and where necessary reposition. Replace damaged components if necessary.

---

Recalls Number (Vehicles Effected)

R/2016/241 (41893)

Manufacturer Reference

NUH

Defect

It has been identified that the bonnet striker support may corrode. If this corrosion is not treated there is a possibility the bonnet striker support may fail which will allow the bonnet to open whilst the vehicle is in motion. Early warning signs or symptoms of corrosion can be seen by the driver around the bonnet striker support and on the leading edge of the bonnet also the bonnet may not lock correctly.

Remedy

Recall affected vehicles to inspect the area around the bonnet striker support and take preventive action to protect the area from corrosion which may include the replacement of the bonnet if required.

---

Recalls Number (Vehicles Effected)

R/2016/229 (787)

Manufacturer Reference

NSV

Defect

In the event of emergency braking or during an ESP regulation phase (e.g. avoiding manoeuvre) the hydraulic block may not prevent the locking of a wheel which could affect control of the vehicle.

Remedy

On affected vehicles replace the braking system hydraulic block

---

Recalls Number (Vehicles Effected)

R/2016/159 (3)

Manufacturer Reference

NSN

Defect

The fuel injectors supply rail could develop a leak over a period of time leading to a drop in fuel pressure in the injector supply rail which can affect the operation of the stop start system. In some extreme cases the engine might not restart and a spray of petrol under the bonnet may occur which is a fire risk.

Remedy

Recall the vehicles that are likely to be affected and check the fuel injector supply rail. Where necessary replace the fuel injector supply rail.

---

Recalls Number (Vehicles Effected)

R/2016/042 (17)

Manufacturer Reference

NRC

Defect

An oil leak could develop at the turbocharger lubrication union retaining bolt due to a non-conformity of this part.

Remedy

On affected vehicles replace the turbocharger lubrication union bolt and its seals.

---

Recalls Number (Vehicles Effected)

R/2016/030 (30)

Manufacturer Reference

NRD

Defect

The tightening torque for the front and rear right hand seat belt lower mountings may not be correct to specification. This could lead to the mountings detaching and in a collision additional injury to the driver.

Remedy

Recall the vehicles that are likely to be affected and rectify the tightening torques for the front and rear right hand seat belt lower mountings.

---

Recalls Number (Vehicles Effected)

R/2015/243 (9483)

Manufacturer Reference

NKA

Defect

The fuel filter's integrated heater may be defective and could cause the cover to distort. This could cause air ingress and fuel egress. Either could cause poor starting and a warning light should illuminate

Remedy

On affected vehicles replace fuel heater cover. Check and if necessary replace connector.

---

Recalls Number (Vehicles Effected)

R/2014/025 (279)

Manufacturer Reference

NAZ

Defect

It has been established that the high pressure fuel rail pipes on the engine have not been torqued to the correct specification. This can result in poor sealing of the rail which can cause as fuel leak onto the engine. If the vaporised fuel comes into contact with a hot engine component there can be a risk of an engine bay fire.

Remedy

Recall all the affected vehicles and retorque the high pressure fuel rail pipes.

---

Recalls Number (Vehicles Effected)

R/2014/021 (2)

Manufacturer Reference

MYQ

Defect

It has been establish that a build up of deposits within the engine can result in engine running and starting issues. In extreme circumstances it can cause a sudden engine stall without any warning.

Remedy

Recall all affected vehicle and install a new software package in the engine management system.

---

Recalls Number (Vehicles Effected)

R/2013/014 (3)

Manufacturer Reference

MUN

Defect

The rear brake caliper mounting bolts may not be to the required torque. Therefore the bolts may slacken and cause noise.

Remedy

Recall the vehicles are likely to be affected to replace the rear caliper mounting bolts and ensure they are correctly torqued.

---

Recalls Number (Vehicles Effected)

R/2012/134 (8)

Manufacturer Reference

MSQ

Defect

The torque settings of the fixings of the front suspension fuel tank fuel cooler and the rear wheels have been set incorrectly. Consequences of the incorrect torque settings include abnormal noise and poor operation of the vehicle.

Remedy

Retighten to the correct torque value the front suspension fixings fuel tank fixings fuel cooler fixing and rear wheel bolts.

---

Recalls Number (Vehicles Effected)

R/2012/061 (6)

Manufacturer Reference

MQF

Defect

The front suspension lower arms may not be fully secure as the mounting bolts may not have been tightened correctly. The driver will initially be alerted to there being a concern because of the abnormal noise that will develop. If the noise is ignored over a long period it is possible the suspension lower arms may detach.

Remedy

Recall the vehicles that are likely to be affected to replace the suspension bolts and tighten them to the correct torque.

---

Recalls Number (Vehicles Effected)

R/2012/048 (78)

Manufacturer Reference

MPX

Defect

The supply terminal to the engine relay unit may have been over tightened and over time this could damage the component and cause the engine to cut out. In addition this could cause the diagnostic warning lamp to illuminate in error and it may make it more difficult to start the engine.

Remedy

Recall the vehicles that are likely to be affected to check and if necessary replace the engine relay unit.

---

Recalls Number (Vehicles Effected)

R/2012/026 (88)

Manufacturer Reference

MPJ

Defect

The fixing bolts of the front LH and RH seat belt return rail may loosen and in cases of extreme force break.

Remedy

The bolts on the left and right- hand sides will be replaced.

---

Recalls Number (Vehicles Effected)

R/2012/011 (15)

Manufacturer Reference

MPB

Defect

The stroke of the brake pedal which could affect the slowing down of the vehicle may be in excess of manufacturer's recommendations due to the brake bleeding operation not being fully performed.

Remedy

Recall the vehicles that are likely to be affected to ensure the brakes have been fully bled and that brake travel is within manufacturer's recommendation.

---

Recalls Number (Vehicles Effected)

R/2011/161 (2)

Manufacturer Reference

MNM

Defect

The nuts that secure the pedal mounting assembly may be the wrong specification. This could allow the nuts to work loose. If this happens control of the vehicle could be effected.

Remedy

Recall all affected vehicles and replace the nuts.

---

Recalls Number (Vehicles Effected)

R/2011/161 (2)

Manufacturer Reference

MNM

Defect

The nuts that secure the pedal mounting assembly may be the wrong specification. This could allow the nuts to work loose. If this happens control of the vehicle could be effected.

Remedy

Recall all affected vehicles and replace the nuts.

---

Recalls Number (Vehicles Effected)

R/2011/039 (10844)

Manufacturer Reference

MHU

Defect

The wiring loom to the tailgate may have been routed incorrectly. This could cause damage to the wiring and amongst other things the boot to open inadvertently.

Remedy

Recall the vehicles that are likely to be affected to check and if necessary replace the tailgate wiring harness.

---

Recalls Number (Vehicles Effected)

R/2011/029 (5)

Manufacturer Reference

MKB

Defect

Gear selection may be affected by inaccurate software being installed.

Remedy

The recalled vehicles will be subject to a software upgrade.

---

Recalls Number (Vehicles Effected)

R/2011/018 (33)

Manufacturer Reference

MJM

Defect

It is possible that the fuel return pipe may chaff on the diesel fuel filter support in the engine compartment. This can if not identified result in a fuel leak.

Remedy

Recall all affected vehicles for the addition of a protective sleeve to the return pipe.

---

Recalls Number (Vehicles Effected)

R/2010/223 (20089)

Manufacturer Reference

MGG

Defect

In very rare circumstances the vacuum pump one way valve may not function correctly which could affect the level of braking assistance.

Remedy

Recall the vehicles that are likely to be affected to replace the brake vacuum pump one way valve.

---

Recalls Number (Vehicles Effected)

R/2009/100 (56)

Manufacturer Reference

MCH

Defect

An internal component of the Brake Master Cylinder may not be in conformity and as such braking performance/efficiency may be affected

Remedy

Recall affected vehicles and replace Master Cylinder

---

Recalls Number (Vehicles Effected)

R/2008/199 (6031)

Manufacturer Reference

MAQ

Defect

An incorrect engine relay unit may have been fitted. This ECU could deteriorate and cause operating faults and perhaps failure of certain equipment

Remedy

Recall affected vehicles check Engine Relay Unit and replace if not correct specification.

---

Recalls Number (Vehicles Effected)

R/2008/051 (2557)

Manufacturer Reference

YES

Defect

The brake pedal might feel stiff and the braking distances extended as a result of a defect in the vacuum pump.

Remedy

Recall the vehicles that are likely to be affected to replace the valve in the vacuum pump.

---

Recalls Number (Vehicles Effected)

R/2008/017 (520)

Manufacturer Reference

YER

Defect

It has been identified that vehicles fitted with 2I HDI engines may have been fitted a vacuum pump which may not be to specification. This could lead to a decrease in braking assistance.

Remedy

Recalled vehicles will have the vacuum pump replaced.

---

Recalls Number (Vehicles Effected)

R/2007/191 (28049)

Manufacturer Reference

YGDYGC &YFB

Defect

It has been identified that the operation of the ABS/ESP braking unit may be affected by the ingress of water.

Remedy

Recall likely to be affected vehicles to reinforce the resistance of the ABS/ESP unit to water.

---

Recalls Number (Vehicles Effected)

R/2007/191 (28049)

Manufacturer Reference

YGDYGC &YFB

Defect

It has been identified that the operation of the ABS/ESP braking unit may be affected by the ingress of water.

Remedy

Recall likely to be affected vehicles to reinforce the resistance of the ABS/ESP unit to water.

---

Recalls Number (Vehicles Effected)

R/2007/191 (28049)

Manufacturer Reference

YGDYGC &YFB

Defect

It has been identified that the operation of the ABS/ESP braking unit may be affected by the ingress of water.

Remedy

Recall likely to be affected vehicles to reinforce the resistance of the ABS/ESP unit to water.

---

Recalls Number (Vehicles Effected)

R/2006/081 (25083)

Manufacturer Reference

XYD

Defect

It has been identified that the front air bag ECU may not take full account of frontal impacts that are below the legal threshold for triggering deployment.

Remedy

Recalled vehicles will have the air bag ECU re-programmed.

---

Recalls Number (Vehicles Effected)

R/2006/037 (6906)

Manufacturer Reference

XXL

Defect

There is a possibility that a seepage of brake fluid may occur at the union between the rear flexi hose and the metal brake pipes. This would eventually lead to the illumination of the low fluid warning lamp which if left would result in longer brake pedal travel and reduced effectiveness of the brakes.

Remedy

Recall the vehicles that likely to be affected and check for seepage of brake fluid. If the brake fluid seepage is apparent the flexible brake hose and the associated metal brake pipes will be replaced.

---

Recalls Number (Vehicles Effected)

R/2005/185 (6772)

Manufacturer Reference

XWZ

Defect

This concern relates to right hand drive vehicles only. There may cases of the brake linkage lever being defectively assembled which may result in a loss of braking efficiency.

Remedy

Recall the vehicles that are likely to be affected check and where necessary reposition the brake pedal relay linkage lever.

---

Recalls Number (Vehicles Effected)

R/2005/176 (12220)

Manufacturer Reference

XWU

Defect

Repeated ingress of saline water into the connections to the Electronic Control Unit for the Anti- Lock Braking system may eventually result in a short circuit that could cause a fire in the engine compartment.

Remedy

Recall the vehicles that are likely to be affected to check the ABS block and strengthen the sealing of the electrical connections.

---

Recalls Number (Vehicles Effected)

R/2005/057 (1286)

Manufacturer Reference

XUU

Defect

The diesel fuel return pipe of the injection system for 1.6 HDI ( DV6) engines carries the risk that over time seeping of fuel may occur due to nonconformity in manufacture.

Remedy

Recalled vehicles will have the return pipe replaced with a quality assured item.