LAND ROVER RANGE ROVER UK Recall Check

---

Recalls Number (Vehicles Effected)

R/2024/167 (1)

Manufacturer Reference

N865

Defect

For the affected vehicle a concern has been identified where the there is an inadequate depth of weld (penetration) between the busbar and the anode in the module of the Plug-in Hybrid Electric Vehicle (PHEV) battery.

Remedy

Replacement of the traction battery.

---

Recalls Number (Vehicles Effected)

R/2024/100 (1)

Manufacturer Reference

N853

Defect

A concern has been identified where the clamps used to secure the fuel injectors into the cylinder head on certain AJ20-D6 engines may crack allowing the injector to come loose. This loose injector could become unseated allowing fuel to be pushed past the injector seal from the combustion chamber or the fuel feed system.

Remedy

A fuel leak in this area could result in fuel spill onto hot engine components which may result in a fire.

---

Recalls Number (Vehicles Effected)

R/2023/360 (4)

Manufacturer Reference

N837

Defect

On affected vehicles there is concern that the structural adhesive applied to the bodyshell has been mis-applied.

Remedy

Install two rivets and seal with approved sealant.

---

Recalls Number (Vehicles Effected)

R/2023/338 (67)

Manufacturer Reference

N845

Defect

On affected Range Rover vehicles fitted with V8 Gasoline NC11 engines the fixings used to secure the engine mounted oil cooler hoses have been found to have inadequate thread engagement.

Remedy

Vehicles will have the engine oil cooler pipe fixings inspected and replaced if required.

---

Recalls Number (Vehicles Effected)

R/2023/244 (2)

Manufacturer Reference

Defect

For certain vehicles the bolt connecting the busbar to the traction battery module connector has not achieved the required clamp force. Arcing at the joint and excessive heat generation cannot be ruled out with the consequence that this may lead to a vehicle fire.?

Remedy

Replacement of the High Voltage battery

---

Recalls Number (Vehicles Effected)

R/2022/341 (7303)

Manufacturer Reference

N759

Defect

On certain 2014 - 2016 Model Year Land Rover Range Rover vehicles the front suspension upper knuckle joint could develop a crack. In extreme cases where a crack in the front suspension knuckle has developed this may lead to detachment of the upper suspension arm.?

Remedy

Carry out an inspection of the front suspension knuckles and replace parts if required.?

---

Recalls Number (Vehicles Effected)

R/2022/341 (7303)

Manufacturer Reference

N759

Defect

On certain 2014 - 2016 Model Year Land Rover Range Rover vehicles the front suspension upper knuckle joint could develop a crack. In extreme cases where a crack in the front suspension knuckle has developed this may lead to detachment of the upper suspension arm.?

Remedy

Carry out an inspection of the front suspension knuckles and replace parts if required.?

---

Recalls Number (Vehicles Effected)

R/2023/163 (5299)

Manufacturer Reference

N784

Defect

On affected 2022 - 2023 Model Year Land Rover Range Rover vehicles the external rear lamp mounted in the body could partially or permanently fail to operate resulting in one or more of the light sources not working.

Remedy

Affected vehicles will have the foam block mounted in the bodyshell removed. The rear lamp mounted in the body and rear tail lamp link lead wiring will be checked for their condition. Where the lamp and wiring are qualified OK no further remedy is required. Where the lamp or wiring are qualified Not OK the lamp will be replaced.

---

Recalls Number (Vehicles Effected)

R/2023/097 (192)

Manufacturer Reference

N783

Defect

On affected vehicles the second row 60% seat frame may have a latch installed with a defective weld. In vehicles that have a defective weld on the second row 60% seat frame latch the seat may not be correctly secured.

Remedy

The rear seat base latch will be inspected. Where the inspection reveals a not OK condition the rear seat 60% frame and associated components will be replaced.

---

Recalls Number (Vehicles Effected)

R/2023/044 (499)

Manufacturer Reference

N763

Defect

For certain 2023 Model Year 3.0L AJ20-P6 Land Rover Range Rover Range Rover Sport Range Rover Velar Discovery and Defender vehicles a small number of engines the cam carrier oil gallery hasn?t been fully drilled. As a result the oil channel could be blocked leading to accumulation of oil against the pressure control valve rubber membrane and subsequently an external oil leak or increased oil carryover into the air intake system.

Remedy

The engine cam carrier will be inspected and where an incorrectly machined cam carrier is found replace it with a correctly machined component. Depending on mileage and engine conditions further associated components may require replacement.

---

Recalls Number (Vehicles Effected)

R/2023/087 (18151)

Manufacturer Reference

N785

Defect

On affected vehicles there is a risk where the water pump pully drive belt can become damaged leading to detachment or destruction. Where water pump pully drive is lost this leads to a loss coolant flow in the engine.

Remedy

Affected vehicles will have the engine coolant elbow replaced. In addition a turbocharger feed coolant pipe will be replaced.

---

Recalls Number (Vehicles Effected)

R/2022/262 (1392)

Manufacturer Reference

N719

Defect

Some of the hot end exhaust bracket fixings may not have been fastened or not have been fastened to the required torque.

Remedy

Check for the presence of the exhaust bracket fixings and where necessary install new fixings or tighten existing fixings to the specified torque.

---

Recalls Number (Vehicles Effected)

R/2022/139 (254)

Manufacturer Reference

N685

Defect

The front crash sensor fixings may not have been installed to the specified level of torque.

Remedy

Check and tighten the front crash sensor fixing to the specified level of torque.

---

Recalls Number (Vehicles Effected)

R/2020/293 (144)

Manufacturer Reference

N496

Defect

The Exhaust Gas Recirculation (EGR) crossover pipe may have been manufactured away from specification.

Remedy

Check and repair the vehicle with a part manufactured to the correct specification.

---

Recalls Number (Vehicles Effected)

R/2019/112 (38)

Manufacturer Reference

N306

Defect

The routing of the electrical harness within the steering column assembly has insufficient clearance.

Remedy

Inspect the steering column electrical harness apply further protective material and repair damaged wiring where required.

---

Recalls Number (Vehicles Effected)

R/2019/013 (219)

Manufacturer Reference

N276

Defect

The crankshaft pulley retaining bolt may fracture due to a production specification error.

Remedy

Replace the crankshaft pulley centre retaining bolt with one that has been manufactured to the correct specification.

---

Recalls Number (Vehicles Effected)

R/2019/015 (2331)

Manufacturer Reference

N277

Defect

The directional indicators may fail to operate.

Remedy

Update the vehicle with the latest software on affected vehicles.

---

Recalls Number (Vehicles Effected)

R/2018/243 (24)

Manufacturer Reference

N227 issue 1

Defect

Autonomous Emergency Braking (AEB) feature will not be available.

Remedy

On affected vehicles download the latest software to the vehicle.

---

Recalls Number (Vehicles Effected)

R/2018/160 (1000)

Manufacturer Reference

N219

Defect

"On certain 2018 and 2019 Model Year Land Rover Range Rover and Range Rover Sport PHEV vehicles where the indicated fuel level on the fuel gauge shows approximately 30% the fuel tank is empty resulting in an engine stall.The vehicle will enter into reduced performance mode and if the customer continues to drive the vehicle will continue to run for circa 8 miles/13Km. The vehicle engine will then cut out without warning. If the traction battery charge status is at least 10% or greater the electric motor will take up drive until such time as traction battery power is depleted. Where the traction battery charge status is below 10% drive from the electric motor is not possible and the vehicle will cut out whilst in motion. All 12 volt powered electrical functions such as power assisted steering exterior lighting and brake assistance will continue to operate as designed.Engine cut out with minimal warning to the driver may lead to an increased risk of an accident."

Remedy

Fit a new revised fuel level sensor float to the vehicle.

---

Recalls Number (Vehicles Effected)

R/2018/036 (1537)

Manufacturer Reference

N138

Defect

The brazing of the fuel rail end caps is inconsistent and may not correctly seal the fuel rail ends. Fuel vapour and liquid fuel leaks can occur over time. This can lead to a liquid fuel leak into the engine bay.

Remedy

On affected vehicles replace the fuel rail with a correctly manufactured version.

---

Recalls Number (Vehicles Effected)

R/2017/288 (14932)

Manufacturer Reference

N124

Defect

Due to a software issue the Instrument cluster may intermittently go blank.

Remedy

Affected vehicles will be recalled to have the latest software installed/downloaded.

---

Recalls Number (Vehicles Effected)

R/2017/138 (5170)

Manufacturer Reference

N029

Defect

The Emergency Locking Retractor in the front passenger safety belt assembly may not function correctly. The Emergency Locking Retractors are equipped with a vehicle-sensitive locking mechanism and a webbing-sensitive locking mechanism. The vehicle-sensitive locking mechanism may not lock as designed. In the event of a pre-crash brake event where the passenger airbag deploys front passenger seat forward facing child seat occupants may sustain more severe injuries.

Remedy

Recall the vehicles that are likely to be affected and replace the left hand front seat belt assembly.

---

Recalls Number (Vehicles Effected)

R/2017/103 (139)

Manufacturer Reference

N026

Defect

The front passenger airbag may not function properly due to a deviation in generant mix ratio. In the event of a crash of sufficient severity the front passenger airbag may not deploy when required. Failure to deploy can lead to increased injuries to the passenger seat occupant.

Remedy

Recall the vehicles that are likely to be affected and replace the front passenger airbag.

---

Recalls Number (Vehicles Effected)

R/2016/307 (452)

Manufacturer Reference

P094

Defect

It has been identified by the air-bag manufacturer that the air-bag initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to non-deployment of the air-bag. Should a collision occur then there is an increased risk of injury to the passenger.

Remedy

Recall all affected vehicles to replace the air-bag with a new quality assured component.

---

Recalls Number (Vehicles Effected)

R/2016/303 (8628)

Manufacturer Reference

P095

Defect

It has been identified by the seat belt Pre-Tensioner manufacturer that the pre-tensioner initiator generant mix ratio does not meet specification. This can therefore result in the initiator not functioning correctly which can lead to none activation of the pre-tensioner.

Remedy

Recall all affected vehicles to check the pre-tentioner and if required replace it with a new quality assured component.

---

Recalls Number (Vehicles Effected)

R/2016/098 (11290)

Manufacturer Reference

PO80

Defect

An incorrectly manufactured crank position sensor may cause the engine to unexpectedly cut out or not to start.

Remedy

On recalled vehicles the engine serial number will be checked and if within the affected range the crank position sensor will be replaced.

---

Recalls Number (Vehicles Effected)

R/2015/187 (152)

Manufacturer Reference

P072

Defect

The second row seat backrest on vehicles with the manual recline second row seat system may not latch robustly in position. It is possible the seat belt may not correctly restrain the occupant in the event of a collision.

Remedy

On affected vehicles inspect the second row seat mechanism and if necessary fit the correct specification components.

---

Recalls Number (Vehicles Effected)

R/2015/119 (35250)

Manufacturer Reference

P068

Defect

The door could be unlatched when in the closed position and no indication provided of an unlatched condition. Vehicle doors not latched in either the primary of secondary state may during driving open. This can increase the risk of a vehicle crash and/or compromise the safety of vehicle occupants and other road users.

Remedy

Recall the vehicles that are likely to be affected and download the latest level of software. A limited number of vehicles may also require a Remote Function Actuator module to be fitted.

---

Recalls Number (Vehicles Effected)

R/2015/036 (926)

Manufacturer Reference

P056

Defect

On affected vehicles the road wheel nuts may not have been manufactured to the correct specification. These wheel nuts may crackwhen subject to shock loads and detach from the stud. This may lead to insecurity and possible detachment of a road wheel.

Remedy

Recall affected vehicles and replace wheel nuts. Locking wheel nuts are not affected.

---

Recalls Number (Vehicles Effected)

R/2015/038 (4860)

Manufacturer Reference

P058

Defect

The ground wiring for the air conditioning blower within the cockpit harness may not be to specification. This can lead to the wire getting hot and melting the plastic insulation and associated burning smell. If ignored and the loom gets significantly damaged there is a possibility of fire.

Remedy

Recall the vehicles that are likely to be affected and replace the earth wire. Where other wiring/insulation is affected necessary repairs will be carried out using the correct repair procedures.

---

Recalls Number (Vehicles Effected)

R/2015/013 (1575)

Manufacturer Reference

P052

Defect

On affected vehicles the servo vacuum hose may have been incorrectly routed and can chafe against the auxiliary drive pulley. This can lead to failure of the hose and a loss of brake servo assistance.

Remedy

On affected vehicles check brake servo hose. If in good condition correctly reroute and secure hose. If hose is damaged replace hose and correctly route and secure.

---

Recalls Number (Vehicles Effected)

R/2015/014 (34134)

Manufacturer Reference

P054

Defect

It is possible that one or both of the front brake hoses could rupture allowing brake fluid to leak. A warning lamp and message will appear on the dash board when the fluid depletes to a certain level. Braking capability will be retained by the rear brake circuit pedal feel will be degraded and pedal travel extended. Stopping distances will increase.

Remedy

Recall the vehicles that are likely to be affected and replace both front brake hoses.

---

Recalls Number (Vehicles Effected)

R/2014/091 (1331)

Manufacturer Reference

P044

Defect

An internal fault can create a short circuit within the fan control module which may lead to overheating of the insulation and ultimately fire within the engine bay. This may happen with the engine switched off and possibly when the vehicle is unattended..

Remedy

Replace electric cooling fan assembly on affected vehicles

---

Recalls Number (Vehicles Effected)

R/2014/040 (9)

Manufacturer Reference

P040

Defect

The right hand rear suspension link arm to knuckle fixings may not be to specification. When subjected to normal use loading one or both of the fixings may fracture. Where one or both of the suspension link arm fixings fracture vehicle stability may be compromised.

Remedy

Recall the vehicles that are likely to be affected and replace both the right hand side rear suspension link arm to knuckle fixings and torque to the correct specification.

---

Recalls Number (Vehicles Effected)

R/2014/039 (1886)

Manufacturer Reference

P042

Defect

In the event of a front direction indictor lamp failure the audible and visual warning (double click/double flash warning) will not function thereby not informing the driver of the failure. This can result in the vehicle not being rectified for a prolonged period which increases the chance of a collision with other road users.

Remedy

Recall the vehicles that are likely to be affected and update the vehicle with the latest software.

---

Recalls Number (Vehicles Effected)

R/2013/091 (49104)

Manufacturer Reference

P033

Defect

It is possible that a leak can occur between the injector spill rail connection and the plastic fuel return pipe. This can cause leakage of fuel which can either pool on the engine cylinder head and then become deposited onto the road surface where it could cause a skid risk to other motorist or if the fuel comes into contact with extremely hot engine components an exhaust manifold for instance it is possible that an under bonnet fire could ensue.

Remedy

Recall all affected vehicles inspect the fuel spill rail/return pipe and if required replace the spill rail with a new modified rail.

---

Recalls Number (Vehicles Effected)

R/2012/153 (51)

Manufacturer Reference

P029

Defect

Mounting bolts for the rear brake caliper may not be torqued to the correct specification. This will create noise from the rear of the vehicle whilst it is being driven and during braking and should warn the driver of the issue. However if the vehicle continues to be driven it is possible the bolts can work loose thus allowing the brake caliper to detach. This will result in the caliper contacting the road wheel which can cause brake failure or sudden deflation of the tyre with subsequent loss of control of the vehicle.

Remedy

Recall affected vehicles to check the mounting bolts and re-torque them.

---

Recalls Number (Vehicles Effected)

R/2012/154 (182)

Manufacturer Reference

P031

Defect

The steering rack mounting bolts may not be fully tight. If the steering gear fixings are below the required torque the driver will experience abnormal noise and feedback through the steering wheel during low speed manoeuvring and at higher speeds some easily corrected minor over steer. If the driver ignores the warning signs both fixings could become sufficiently loose to detach from the vehicle making directional control of the vehicle difficult.

Remedy

Recall the vehicles that are likely to be affected to inspect the steering gear and check the steering gear mounting fixings are tightened to the correct torque.

---

Recalls Number (Vehicles Effected)

R/2012/116 (5)

Manufacturer Reference

P028

Defect

"The affected vehicles windshield may not be fully bonded in to the aperture. Where the windshield is not bonded water ingress might occur and there may be reports of increased wind noise. Furthermore this concern may also be a non-compliance with the regulatoryrequirements of FMVSS 212 or FMVSS 216 Windshield Mounting."

Remedy

Approved Service Centre will remove and replace the windscreen with the correct bonding agent in line with existing service repair procedures.

---

Recalls Number (Vehicles Effected)

R/2010/147 (255)

Manufacturer Reference

P021

Defect

The front pump bearing on some aftermarket replacement High Pressure Fuel Pumps may fail due to lack of sufficient lubrication. This will cause failure of the shaft seal which will cause a fuel leak and if not rectified could cause a vehicle fire.

Remedy

Recall affected vehicles and replace fuel pump with the latest specification pump.

---

Recalls Number (Vehicles Effected)

R/2009/069 (77)

Manufacturer Reference

P018

Defect

The windscreen bonding process to vehicle may not be effective. Water and wind ingress may occur. In extreme cases in an air bag deployment or collision the windscreen may detach.

Remedy

Recall affected vehicles to check for presence of primer/activator on REAR tailgate glass. If present no further action is required as all screen security is assured. If not present the FRONT windscreen will be removed and re-fitted in-line with exiting service repair procedures.

---

Recalls Number (Vehicles Effected)

R/2006/218 (23)

Manufacturer Reference

A054

Defect

Brake fluid may leak from either the right hand front or left hand front brake caliper bridge pipe

Remedy

Recall affected vehicles and replace the caliper bridge pipe on all four calipers with a revised corrosion resistant part.

---

Recalls Number (Vehicles Effected)

R/2005/156 (917)

Manufacturer Reference

A023

Defect

Due to the presence of an out of specification component within the automatic gearbox parking brake interlock system. The parking function may not fully engage when the operating lever is moved to park despite all indicators showing that park has been achieved. If the parking brake is not applied the vehicle may roll away.

Remedy

Recalled vehicles will have the out of specification component replaced with a quality assured item.

---

Recalls Number (Vehicles Effected)

R/2004/069 (21191)

Manufacturer Reference

a156

Defect

Due to a material specification change combined with inadequate tool design and process control it is possible that stress cracking can occur at either the fuel tank vent valve ring welding the breather pipe weld or the filler pipe stub.

Remedy

Replace the fuel tank with an improved design.

---

Recalls Number (Vehicles Effected)

R/2005/008 (891)

Manufacturer Reference

Defect

It has been identified that the TV will be viewable by the driver whilst the vehicle is in motion if the TV is being operated in the full screen position when the vehicle is stationary and a call through the in car phone system is either made or received and not ended prior to the vehicle being set in motion.

Remedy

Recalled vehicles will have the high level front display unit reprogrammed with a revised level of software thus ensuring that the TV screen is switched off whilst the vehicle is in motion.

---

Recalls Number (Vehicles Effected)

R/2004/193 (49)

Manufacturer Reference

A178

Defect

On certain vehicles equipped with a dynamic stability control the yaw rate sensor may have suffered internal delamination. This could result in actuation of the stability control incorrectly resulting in uneven and unexpected application of the brakes.

Remedy

Recalled vehicles will be inspected in order to ascertain whether they contain a suspect sensor. Should this indeed be the case the sensor will be replaced with a quality assured part.

---

Recalls Number (Vehicles Effected)

R/2002/035 (1097)

Manufacturer Reference

279

Defect

There is a possibility that a short circuit may occur in the cigar lighter bulb holder when the vehicle lighting system is operated.

Remedy

Disconnect the illumination feed to the lighter and remove the bulb.

---

Recalls Number (Vehicles Effected)

R/2000/074 (17603)

Manufacturer Reference

219

Defect

There is a possibility of premature failure of the cooling system hoses and throttle body heater gasket. Expelled coolant allowed to remain on hot engine components can result in the evaporation of the water content and leave an artificially high concentration level of anti - freeze which is in extreme circumstances both corrosive and inflammable.

Remedy

Recall affected vehicles to replace cooling system hoses / throttle body heater gasket with quality assured parts.

---

Recalls Number (Vehicles Effected)

R/1998/003 (15175)

Manufacturer Reference

Defect

Involuntary operation of the air bag may occur as a result of an intermittent electrical fault.

Remedy

Recall the affected vehicles for the fitment of a safety fuse link in the air bag circuit.

---

Recalls Number (Vehicles Effected)

R/1996/032 (2805)

Manufacturer Reference

Defect

The rear suspension composite links are below specification and may develop small stress cracks at the aluminium eye end. Failure of the link(s) would affect the security of the rear axle.

Remedy

Recall the affected vehicles for replacement of the suspension links with quality assured examples.

---

Recalls Number (Vehicles Effected)

R/1993/032 (1415)

Manufacturer Reference

Defect

The window operating switch may latch in the 'pressed' condition. This could result in the window continuing to operate up or down when pressure on the switch is released.

Remedy

Recall the affected vehicles for replacement of the original window switches with quality assured units.