Date From | Date To | Concern |
---|
21/07/21 | | Raised: 15/06/22 - ELECTRICAL CONNECTIONS OF 48 VOLT POWER SYSTEM MIGHT NOT BE PROPERLY TIGHTENED View/hide..
Recalls Number (Vehicles Effected)R/2022/188 (6)
Manufacturer Reference508
DefectPossible insufficient tightening on electrical connections of 48 volt power system.
RemedyGain access to the battery system and check tightness of connections to the 48 volt power system. resecure if required.
|
14/04/22 | | Raised: 15/06/22 - POSSIBLE GEARBOX ELECTRICAL CABLE CONTACT WITH CATALYST THERMAL SHIELD. View/hide..
Recalls Number (Vehicles Effected)R/2022/189 (1)
Manufacturer Reference509
DefectPossible gearbox electrical cable contact with Catalyst thermal shield.
RemedyCheck and ensure the correct positioning of the gearbox wiring harness in relation to the catalytic convertor shield if required replace the wiring harness.
|
24/08/21 | | Raised: 16/05/22 - SUPPLY CABLES FOR THE 48 VOLT BATTERY SYSTEM HAVE AN INCORRECT TIGHTENING TORQUE View/hide..
Recalls Number (Vehicles Effected)R/2022/159 (122)
Manufacturer Reference503
DefectSupply cables for the 48Volt battery system have an incorrect tightening torque.
RemedyInspect and retighten cable fixing screws for the 48Volt battery system.
|
24/01/22 | | Raised: 22/04/22 - THE TAIL LAMP MAY START FLICKERING WHEN RECEIVING A VOLTAGE CLOSE TO THE MAXIMUM (16V) View/hide..
Recalls Number (Vehicles Effected)R/2022/138 (20)
Manufacturer Reference501
DefectWhen the tail-lamp is receiving a voltage close to the maximum (16V) the tail-lamp may start flickering.
RemedyCheck the production date of the tail-lamps if the fitted lamps are within the defective range replacement of the rear lamp/lamps will be required.
|
28/09/21 | | Raised: 03/12/21 - WRONG TYPE VARIANT VERSION ON STATUTORY PLATE. View/hide..
Recalls Number (Vehicles Effected)R/2021/441 (37)
Manufacturer Reference450
DefectWrong TVV (Type-Variant-Version) on statutory plate.
RemedyReplace label located on B Pillar
|
28/01/21 | | Raised: 15/11/21 - POSSIBLE FUEL LEAKAGE IN ENGINE BAY View/hide..
Recalls Number (Vehicles Effected)R/2021/406 (58)
Manufacturer Reference442
DefectA deviation of the P/T sensor moulding process of the plastic housing. Possible Fuel Leakage in engine bay Loss of power potential fire risk in worst case.
RemedyReplacement of the short fuel line containing the pressure sensor.
|
24/08/21 | | Raised: 12/10/21 - EXHAUST ACTIVE VALVE CABLE MAY SHORT CIRCUIT DUE TO CONTACT WITH THE EXHAUST SYSTEM View/hide..
Recalls Number (Vehicles Effected)R/2021/388 (56)
Manufacturer Reference444
DefectExhaust active valve cable may short circuit due to contact with the exhaust system.
RemedyCheck cable layout reposition and repair if necessary.
|
13/07/21 | | Raised: 12/10/21 - INCORRECT AUTOMATIC TIGHTENING OF AN ELECTRICAL CABLE ON PRODUCTION View/hide..
Recalls Number (Vehicles Effected)R/2021/389 (3)
Manufacturer Reference441
DefectIncorrect automatic tightening of an electrical cable on production.
RemedyCheck and retighten the connection.
|
09/04/21 | | Raised: 28/04/21 - THE ELECTRONIC POWER STEERING FUNCTION MAY NOT BE AVAILABLE View/hide..
Recalls Number (Vehicles Effected)R/2021/195 (11)
Manufacturer Reference419.
DefectThe Electronic Power Steering function may not be available.
RemedyReplacement of steering rack.
|
23/03/21 | | Raised: 23/04/21 - FRONT TYRES OUTER TREAD MAY HAVE BEEN DAMAGED View/hide..
Recalls Number (Vehicles Effected)R/2021/196 (7)
Manufacturer Reference418.
DefectFront tyres outer tread may have been damaged.
RemedyCheck and replace tyre if required
|
09/01/19 | | Raised: 16/03/20 - THE FINAL PART OF THE VEHICLE VERSION DISPLAYED ON THE MANUFACTURER LABEL ON THE A PILLAR CONTAINS INCORRECT VERSION INFORMATION View/hide..
Recalls Number (Vehicles Effected)R/2020/180 (1)
Manufacturer Reference393
DefectIncorrect sticker shows data M1561F4 5W correct version is M1561F 4APD.
RemedyReplacement of the sticker label.
|
11/08/17 | | Raised: 24/07/19 - FRONT HEADLAMPS FULL LED VERSION HEADLAMP VERTICAL BEAM OUT OF COMPLIANCE View/hide..
Recalls Number (Vehicles Effected)R/2019/239 (320)
Manufacturer Reference387
DefectFront headlamps full LED version headlamp vertical beam out of compliance.
RemedyCheck and adjustment of the front headlamp vertical beam.
|
10/10/18 | | Raised: 25/06/19 - BLIND SPOT DETECTION SYSTEM HAS BEEN MARKED WITH INCORRECT ECE CERTIFICATION LABELLING View/hide..
Recalls Number (Vehicles Effected)R/2019/199 (11)
Manufacturer Reference376
Defect"Blind spot detection system has been marked with the wrong ECE certification labelling."
RemedyAttaching the correct label to the left and right rear blind spot sensors and within the owners quick reference guide.
|
04/12/17 | | Raised: 11/06/18 - POSSIBLE INCORRECT WELDING View/hide..
Recalls Number (Vehicles Effected)R/2018/179 (1)
Manufacturer Reference369
Defect"Possible incorrect welding due to human error of the 4 sections of the front engine under frame. This has been caused by an interruption in the welding processPossible brake of the welds Sub-frame can lost the correct alignment and the vehicle could lose the stability"
RemedyInspection of the welded points if welding Is defective replacement of the front sub-frame required
|
19/09/16 | | Raised: 03/08/17 - UNEXPECTED LOSS OF ENGINE POWER View/hide..
Recalls Number (Vehicles Effected)R/2017/236 (125)
Manufacturer Reference349
DefectThe short hose on the pipe between the turbocharger and the intercoolers could break during the normal use of the vehicle. This could result in loss of performance and cause the check engine light to illuminate as the hose material may not conform to manufacturers specification.
RemedyReplace the short hose on the pipe between the turbocharger and the intercoolers. In some cases the replacement of the entire intercooler pipe will be necessary; this will be determined by the VIN number.
|
07/02/13 | | Raised: 10/07/17 - POSSIBLE SHORT CIRCUIT OF DRIVER SEAT WIRING View/hide..
Recalls Number (Vehicles Effected)R/2017/235 (3844)
Manufacturer Reference342
Defect"Some vehicles may have been manufactured with an incorrect driver seat wiring harness layout which can cause the seat wiring harness to rub against metal points on the seat/seat frame assembly through normal seat adjustment operation. Over time this can lead to aninoperative seat adjustment system and in rare cases a potential risk of fire due to an electrical short to ground between the seat wiring harness and the seat adjustment motor assembly."
RemedyReplace 2 seat circuit breakers with 25 amp mini-fuses check harness apply protective barrier and reposition if undamaged. If damaged replace harness and then ensure repositioned and protective barrier applied.
|