NISSAN PATROL UK Recall Check

---

Recalls Number (Vehicles Effected)

R/2018/100 (27623)

Manufacturer Reference

PG8BA / PS8B0

Defect

In 2013 Nissan announced a Recall campaign to replace Takata SPI front passenger airbag inflators. A non-dessicated passenger airbag inflator was used for the replacement. Although there have been no known incidents associated with inflators of this type Nissan has decided to replace all inflators previously repaired with a non-dessicated inflator to a new dessicated version.

Remedy

Replace the front passenger airbag inflator with a new dessicated type.

---

Recalls Number (Vehicles Effected)

R/2017/279 (39318)

Manufacturer Reference

"PG7BOPS7B2R1723"

Defect

The air bag inflators on affected vehicles were previously checked and deemed to be serviceable. As a precautionary measure the manufacturer has decided to replace them with new assemblies.

Remedy

On affected vehicles replace air bag assembly.

---

Recalls Number (Vehicles Effected)

R/2017/039 (9)

Manufacturer Reference

Defect

"The airbag manufacturer have informed Nissan of a potential concern with propellant degradation of Front Passenger Airbag fitted with Smokeless Passenger Inflator (SPI). It has been confirmed that this degradation is a function of time temperature and environmental moisture. Deterioration of the Inflator propellant may under certain usage conditions lead to abnormal deployment of the Passenger Airbag. In an extreme situation this condition could create excessive pressure within the inflator during airbag deployment and may resultin separation of the airbag housing."

Remedy

Recall all affected vehicles to replace the front passenger airbag module with a new quality controlled item.

---

Recalls Number (Vehicles Effected)

R/2015/093 (99525)

Manufacturer Reference

Defect

The manufacturer has identified that a potential air leak at the passenger airbag inflators which may allow moisture to enter the airbag inflator causing the propellant in the inflator units to deteriorate. Deterioration of the propellant may lead to abnormal deployment of the passenger airbag. In an extreme situation this may result in separation of the airbag housing during deployment causing injury to occupants.

Remedy

Inspect air bag assembly and where required replace air bag inflator

---

Recalls Number (Vehicles Effected)

R/2013/109 (113)

Manufacturer Reference

R1306

Defect

It has been identified that the accelerator pedal position sensor located in the accelerator pedal assembly may provide an incorrect signal due to sensor terminal wear. If this occurs the ECM will detect the sensor failure and illuminate the engine management waning lamp on the dash. It will also control and` limit vehicle acceleration. However in extreme case if this situation occurs and there is excessive dust in the throttle valve which could affect the amount of intake air then the engine could stall at idle speed.

Remedy

Recall all affected vehicles and replace the throttle pedal assembly.

---

Recalls Number (Vehicles Effected)

R/2013/050 (59008)

Manufacturer Reference

PG3B7 / PS3B2

Defect

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Remedy

Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

---

Recalls Number (Vehicles Effected)

R/2013/050 (59008)

Manufacturer Reference

PG3B7 / PS3B2

Defect

The subject vehicles are equipped with front passenger airbag inflators which could have been assembled with improperly manufactured propellant wafers. Improperly manufactured propellant wafers could cause the inflator to rupture and the front passenger airbag to deploy abnormally in a crash. This could result in increased risk of injury to the occupant and the possibility of a fire.

Remedy

Recall the vehicles that are likely to be affected to inspect and where necessary replace the airbag inflator module.

---

Recalls Number (Vehicles Effected)

R/2010/077 (4)

Manufacturer Reference

R1020

Defect

The combustion rate of the airbag propellant may be too fast causing excessive internal pressure in the inflator during airbag deployment. In an extreme case the inflator casing may rupture leading to a scattering of metal fragments.

Remedy

Recall the vehicles that are likely to be affected to replace the front passenger airbag assembly.