Date From | Date To | Concern |
---|
21/04/15 | | Raised: 05/12/19 - A CONDENSER MAY FAIL DUE TO INADEQUATE HEAT TREATMENT IN THE AIRBAG CONTROL UNIT View/hide..
Recalls Number (Vehicles Effected)R/2019/422 (1634)
Manufacturer Reference69Z6
DefectA condenser may fail because of inadequate heat treatment in the airbag control unit.
RemedyThe Airbag Control Unit must be reprogrammed in all affected vehicles.
|
01/03/11 | | Raised: 07/03/18 - STARTER MOTOR MAY MALFUNCTION AND OVERHEAT View/hide..
Recalls Number (Vehicles Effected)R/2018/060 (1943)
Manufacturer Reference27F7
DefectOn vehicles with diesel engines and stop/start system the starter motor may be permanently activated because the return spring in the solenoid switch is bent or broken. If the permanent current supply to the starter motor is not noticed overheating of the component with local scorching damage and a vehicle fire is possible.
RemedyRecall the vehicles that are likely to be affected and replace the solenoid switch.
|
13/09/16 | | Raised: 29/01/18 - PASSENGER AIRBAG MAY NOT DEPLOY AS INTENDED View/hide..
Recalls Number (Vehicles Effected)R/2018/032 (24)
Manufacturer Reference69T1
DefectDue to a process deviation in the production front passenger airbag module the connection between detonator and generator may not be sufficient. This may cause the airbag not to deploy as intended.
RemedyOn affected vehicles replace the front passenger air bag module with a correctly manufactured version.
|
27/01/15 | | Raised: 06/04/16 - SIDE AIRBAG GAS GENERATOR CANISTER MAY FAIL View/hide..
Recalls Number (Vehicles Effected)R/2016/064 (35)
Manufacturer Reference69M2
DefectFor certain vehicles manufactured within a specific period it is possible that the gas generator housing may be damaged if a side airbag is deployed. If the airbag/s were deployed the gas generator could explode and dislodge small metal parts which could cause injury to the vehicle occupants.
RemedyRecall the vehicles that are likely to be affected and check the dates of manufacture for the left and or right side airbags. Where a possibly affected airbag is found it will be replaced.
|
01/11/02 | | Raised: 02/06/06 - TWIN-MASS FLYWHEEL MAY FAIL AND RESULT IN A VEHICLE FIRE View/hide..
Recalls Number (Vehicles Effected)R/2006/059 (1085)
Manufacturer Reference13S3
DefectIt has been advised that the twin-mass flywheel can become damaged because of poor internal installation. This can result in a failure of the twin-mass flywheel and under unfavourable circumstances a vehicle fire.
RemedyRecalled vehicles will have the twin-mass flywheel replaced.
|
01/03/04 | | Raised: 18/02/05 - BOLTS OF THE TANDEM FUEL PUMP COVER MAY BREAK View/hide..
Recalls Number (Vehicles Effected)R/2004/212 (5492)
Manufacturer Reference20S3
DefectIt is advised that on some vehicles fitted with a 3 and 4 cylinder pump injector engine the bolts of the tandem fuel pump cover may break due to a bolt production fault. As a result the pump housing will not be tight and a diesel fuel leak may occur.
RemedyRecalled vehicles will have the pump checked for being of a certain manufacture. If found to be within the affected range the pump housing cover bolts will be replaced.
|
06/11/01 | | Raised: 23/07/02 - WINDSCREEN WIPER MOTOR MAY FAIL View/hide..
Recalls Number (Vehicles Effected)R/2002/046 (437)
Manufacturer Reference92S1
DefectThe windscreen wiper motor may cease to work because of an electrical software fault.
RemedyReplace the windscreen wiper motor of all affected vehicles.
|
01/08/96 | | Raised: 15/01/99 - POTENTIAL FAILURE OF BATTERY CHARGING CIRCUIT View/hide..
Recalls Number (Vehicles Effected)R/1998/107 (113)
Manufacturer Reference
DefectThe power supply of the vehicle can be disrupted without warning (the alternator warning light does not illuminate) due to a break in the wiring loom at the alternator connector.
RemedyRecall affected vehicles and fit new wiring loom.
|
| | Raised: 05/02/97 - OVERHEATING OF BRAKE PADS View/hide..
Recalls Number (Vehicles Effected)R/1996/112 (463)
Manufacturer Reference
DefectThe brake servo may not release fully allowing the brake pads to remain in contact with the brake discs. This could result in possible overheating and loss of braking efficiency.
RemedyRecall the affected vehicles for the fitment of an additional pull off spring to the brake servo.
|